Designed for the DIY community

Panasonic TY-LA1000 Replacement TV Lamp
TY-LA1000

PT-43LC14
PT-50LC14
PT-60LC14
PT-50LC13
PT-60LC13
PT-50LCX63
PT-60LCX63
PT-43LCX64
PT-50LCX64
PT-60LCX64
PT-44LCX65
PT-52LCX65


    
     Did your TV stop working and you are not sure if it is the lamp?  Did you install a new lamp and your TV is not working properly?  View our troubleshooting/repair guide to help you identify the problem.  Just click on button above to begin the guide.  We hope you will find this helpful.



     Click on the link below to purchase this lamp.  River Valley Electronics
offers factory original lamps at great prices with FREE shipping included.  Orders received by 3 PM EST will ship same business day!

Click here to purchase your Panasonic TY-LA1000 replacement lamp!!!




    Purchasing the lamp only and replacing the bad lamp in your existing housing is a very cost effective way that can save you up to hundreds of dollars. The lamp installation is simple and takes only minutes to complete. The plastic housing surrounding the lamp is completely reusable. Picture quality and brightness will not be affected by reusing the housing. We can safely say that because we have thoroughly tested this on every lamp we give advice on. If you do purchase the complete lamp in housing you should have your old lamp housing recycled because it contains mercury.  It is also against many state laws to throw this product in the trash.  It is highly recommended when you purchase a lamp replacement to buy a
factory original OEM (original equipment manufacturer) lamp. The two manufacturers of lamps that TV companies use are Osram and Philips. Some companies may debate that Philips lamps are better than Osram or vice versa, but that is only opinion (or sales tactics) as there are no statistics proving one is better than the other. We have extensively tested (over 25,000 testing hours) each brand and neither performs better or lasts longer than the other. Purchasing a lamp of any other brand is an "OEM compatible", generic, or aftermarket lamp (DNGO, APO).  This is not advised because these lamps have a fraction of the lamp life and can possibly damage your TV.



     Detailed written instructions of the lamp installation are for provided below showing how to replace the lamp in the TY-LA1000 housing. 


1)         Please use the included latex-free glove when handling the lamp.  Failure to use the glove during handling may reduce the life of the lamp.  The TV must be unplugged from the outlet before removal of the lamp.  It must stay unplugged until you are completely finished. The lamp door is located in the front of the TV.  The TV has a front cover that pulls off to expose the lamp door.  Ensure proper cooling before removing the old lamp.

 

2)         Lay the assembly lamp down. There are two Philips head screws in the corners opposite the plastic handle.  When looking at the metal side of the housing opposite the plastic handle, insert the screw driver in the top hole, there is one screw. The metal housing should now come off by lifting up on the housing.  Please note: You will need to reuse the existing connector from your housing. Cut the leads off of the lamp. Make sure to cut them close to the lamp, so you have plenty of wire.  Take out the two Philips head screws and take out the metal brackets and one metal piece under the bracket. Discard the small upright piece that is under the top bracket.

 

3)         Place the new lamp in the housing. Screw the brackets back in to hold the lamp.  Bend the wire around the screw that goes in the side of the lamp and screw it in, clamping the wire down. Hold the tab that you are screwing the screw into so you do not break the filament. Repeat with the nut on the top of the lamp.  The post on the top of the lamp is very fragile.  DO NOT OVER TIGHTEN AND USE CARE OR DAMAGE MAY OCCUR.  Companies will not warranty installation damage.  Reassemble the cage and insert into television.  Put TV completely back together and plug into the wall outlet.

 

4)         Reset the lamp timer with the following procedure depending on your model TV. PT-50LC13/PT-60LC13/PT-50LCX63/PT-60LCX63/PT-43LCX64/PT-50LCX64/PT-60LCX64.  1) Make sure the TV is on.  2) While pressing and holding down VOL DOWN button on the TV, press and hold down PIP button on the remote until a message appears on the screen that the lamp timer has been reset. 

 

5)         PT-43LC14/PT-50LC14/PT-60LC14.  1) Make sure the TV is on.  2) While pressing and holding down VOL DOWN button on the TV, press and hold down SPLIT PLAY button on the remote until a message appears on the screen that the lamp timer has been reset. 

 

6)         PT-44LCX65/PT-52LCX65/PT-61LCX65/PT-52LCX15. 1) Make sure the TV is on.  2) While pressing and holding down VOL DOWN button on the TV, press and hold down the SPLIT DVD/VCR CH UP button on the remote until a message appears on the screen that the lamp timer has been reset.  If this does not work, use SPLIT DVD/VCR CH DOWN instead.


- nice2 - price5